Deploying HyperScale Edge With Tagged vLAN

HyperScale Edge node can be deployed in environments with tagged virtual LANs (VLANs).

Note

When the deployment is complete, the password based root access is disabled and firewall and ransomware protection settings are enabled on the node automatically.

Before You Begin

Verify the requirements needed to setup the VLAN Topology in your environment.

Tip

Keep the network names and IP addresses listed in the Network Requirements section of VLAN Topology handy before you start the configuration.

Procedure

Log on to one of the nodes using the system console as described in Setting up the installation media. (Do not use PuTTy / SSH to setup the nodes.)
Launch the network configuration interface using the following command:
```
# hssetup
```
The HyperScale Edge Installer page appears.
Click Start.

The Network Configuration page appears.
Configure the routable data protection VLAN interface as follows:
1. Click Create VLAN.
  
  The Create VLAN dialog box appears.
2. From the Interfaces list, select one of the data protection interfaces. (For example, enpsf3 or enpsf5.)
  
  Tip
  
  Hover the cursor over the interfaces to display the speed and MAC address of the physical interface.
3. In the VLAN ID box, enter the VLAN ID associated with the routable VLAN network and then click CREATE.
  
  The interface appears with the VLAN ID in the Network Configuration page. (The VLAN ID will be different, depending on the VLAN ID in your environment.)
4. From the Network Type list, select CommServe Registration.
  
  Note
  
  This network will perform the same role as the data protection network and will also be used to register the node to the Server Gateway.
5. Add the IP Address and Netmask in the respective boxes.
  
  Once completed your screen should be similar to the one shown in the following image:
Configure additional data protection VLAN interfaces as follows:

(Repeat this step to add all the VLANs available in your environment.)
1. Click Create VLAN.
  
  The Create VLAN dialog box appears.
2. From the Interfaces list, select one of the data protection interfaces. (For example, enpsf3 or enpsf5.)
  
  Tip
  
  Hover the cursor over the interfaces to display the speed and MAC address of the physical interface.
3. In the VLAN ID box, enter the VLAN ID associated with the VLAN network and then click CREATE.
  
  The interface appears with the VLAN ID in the Network Configuration page.
4. From the Network Type list, select Data Protection.
5. Add the IP Address and Netmask in the respective boxes.
  
  Repeat this step to configure ALL the VLANs available in your environment.
  
  Once completed your screen should be similar to the one shown in the following image: (The VLAN IDs and the number of VLANs will be different, depending on the VLAN configuration in your environment.)
Configure the DNS server(s) as follows:
1. In the Default Gateway box, add the IP address associated with the default gateway.
2. In the DNS Servers box, add the IP address associated with the DNS Server.
  
  Click the ADD button to add additional DNS servers. A maximum of 3 DNS servers can be added.
  
  Note
  
  Multiple DNS servers are recommended.
  
  Once completed your screen should be similar to the one shown in the following image: (The number of DNS servers may vary depending on the number of servers available in your environment.)
3. Click CONFIGURE.
  
  The software validates the network and will take a few minutes to complete.
  
  The Network Configuration Summary dialog box appears.
Verify the network configuration and then click CONTINUE.

Verify the following information.
- All the VLANs are included.
- IP address and Netmask for the VLANs are accurate.
  
  Note
  
  Hostname and serial number associated with the node is accurate.
  
  If you need to change the Hostname do so now. To change the hostname modify and correct the DNS records, (forward and reverse records) as discussed in Setting Up the DNS.
- Default gateway and DNS servers are accurately configured.
  
  Note
  
  If an error is found, or if the hostname was changed, click CHANGE CONFIGURATION to go back and correct the values.
  
  The Node Details dialog box appears.
Add the following information:
1. In the Root password and Confirm password boxes, type a secure password for the nodes.
  
  Tip
  
  Hover the cursor over the Root password box to view the password requirements.
2. In the Disk library Storage pool name box, type a name for the storage pool associated with the cluster.
  
  The storage pool name can include numbers and alphabets. Special characters cannot be used in the storage pool name.
  
  Tip
  
  Note down the storage pool name. This will be helpful to identify the storage pool in the Metallic console.
3. From the Time zone list, select the time zone in which the nodes are located.
4. In the Password for Restricted shell user - cvbackupadmin and Confirm cvbckupadmin password boxes, type a secure password for the cvbackupadmin user.
5. Click NEXT.
  
  Note
  
  The setup process configures the network for the node. This will take some time to complete.
The Deployment Information page appears.
Click Connect to Commvault Cloud SaaS, and then click NEXT.

The Credentials page appears.
Choose one of the following options to connect to the CommServe:
1. To connect using the user credentials, in the UserName and Password tab, provide the following details:
  1. In the Commvault Cloud SaaS proxy hostname box, enter the fully qualified host name of the existing Server Gateway that you are connecting to.
    
    Note
    
    TCP Ports 8400 & 443 must be open from the nodes to the Server Gateway for the registration to work.
  2. In the Username and Password boxes, enter the credentials of the tenant admin user that must be used to access the Server Gateway and then click NEXT.
2. To connect using an authorization code, enter the following information.
  
  Note
  
  When you install using an authorization code, the installation process does not create the disk storage pool automatically. You must manually create the storage pool from the Command Center after the installation. For more information, see Creating a Disk Storage Pool.
  1. Click the AUTH-CODE tab.
  2. In the Commvault Cloud SaaS proxy hostname box, enter the fully qualified host name of the existing Server Gateway that you are connecting to.
    
    Note
    
    TCP Ports 8400 and 443 must be open from the nodes to the Server Gateway for the registration to work.
  3. In the Auth-code box, enter the authorization code.
  4. Click NEXT.
The software validates the information and will start the installation process. This process may take some time (approximately 45 minutes) to complete. You can monitor the progress using the progress bar.

Caution

Do not reboot or stop the installation during this process.

The completion message is displayed once the installation is completed.
Click CLOSE.

What to Do Next

Complete the additional configurations that may be required to customize your environment. For more information, see What to do Next.